Driveshaft Vibrations Problems Chevy Colorado

This challenge is usually caused by used or worn u-joints or dings and dents in lyour tubing. We can offer support and tips for u joint maintenance for your Chevy Colorado Pickup. 

Running raised trucks with larger tires, are you changing the transfer case model, or transmission. If you have a two piece driveshaft it's important to balance the complete assembly at the same time, just contact us (800-216-1632) we will help you get rid of vibration problems. See our free information on how to keep up or troubleshoot driveline and with angle phasing concerns.

Driveshaft Failure Symptoms Chevy Colorado

New or strange noises from under the vehicle are a symptom of a problem with the driveshaft. These noises can emulate from the following:

Failure of Transmission or T-Case rear bushing or driveshaft center support bearing will facilitate driveshaft malfunction. Driveshaft U-joints excessive wear or failing will interfere with the driveshaft’s ability to rotate properly. This will cause; rattling, clunking, scraping, or even squeaking sounds.

U-joints might be operating dry of lubrication may also produce a squeaking noise at lower speeds. Clicking or knocking sounds specifically can indicate a faulty CV joint. Any noises such as these are an indicator that your vehicle is ready for maintenance. Problems with turning the vehicle is another likely sign of a bad driveshaft. A broken driveshaft can prevent wheels from turning properly, giving you trouble when trying to make turns. This issue limits your overall control of the truck. These issues can prevent you from driving the truck correctly.

Shuddering Problem with Chevy Colorado Driveshafts

Experiencing a significant shudder when accelerating from low speed or a stopped position, it can be another sign of failing driveshaft component. A U-joint or bad center bearing within the driveshaft may cause the faltering acceleration. You may also hear sounds while the truck is shuddering from the worn-out U-joint. Driveshaft  failure at freeway speeds is traumatic, don’t let it happen to you or your wife.

Driveshaft Modifications Chevy Colorado Truck

Vehicles with 4 x 4 off road and 4wd Pickups tend to be harder on the driveshafts. We offer both front and rear shafts plus customized shafts (for your application) if required. New OEM shafts as well as re-manufactured driveshafts are available, let us repair your existing driveline assembly and you save money.

When you are modifying your vehicle the drivelshaft often needs modifying to; Lifting or lowering the suspension, swapping transmissions or axles, 4x4s, rock crawlers, hotrods, customs, all of these things usually require drive shaft modification to be done correctly. 

We are able to fabricate over 100 different driveshafts configuration for the Chevy Colorado cars and pickups. We also provide a  full assortment of new Spicer Dana and NEAPCO yokes, u-joint parts, and flanges, existing  shafts reduced or lengthened.

Also, heavy duty industrial shafts are one of our primary products areas such as over the highway 18 wheeler, farming, building, construction and mining shafts. We also have a large stock of power take off shaft (PTO). Double and individual CV joint shafts created for vehicles with perspective problems (angle) are available, along with shafts designed to your particular engineering and design specs.

The essential function of your driveshaft is always to transmit energy from a point (rear of transmission or transfer case to another point with constant action. In construction, trucks and pickups, the drivetrain was created to send torque through angles from your transmission for the axle (or auxiliary transmission). The driveshaft must go through

constantly changing general viewpoints (angles) in the middle the transmission and axle. It must also be able to transforming size while transmitting torque (by way of the slide yoke). rides suspended by springs inside an unusual, hovering motion. This indicates the driveshaft must have the capacity to broaden, change and contact working perspectives, when experiencing protrusions or depressions. This is often accomplished through common joint parts, which permit the driveline to be used at divergent angles, in addition to slip yokes, which allow contraction or growth to happen.

When your drive/shaft  is not well-balanced with all the genuine yoke and U-joint components, you could have not repaired the possible vibrations. Our facility features the newest in driveshaft  production, and precision equipment and tooling. 

High Speed Balancing is the key to remove vibrations, vibration totally free for your Chevy Colorado !

A driveshaft is not planning to operate clear and vibrations free unless it is right plus in balance. Our shafts are, right after set up and before welding, pre-straighten inside a unique hydraulic tool, it is actually straightened to improve than factory specifications. We then dynamically highspeed harmony of the whole shaft assembly.

Want to review our detailed high quality  driveline manufacturing process we have provided a detailed video. We also specialize in high end service, if you are delivering to us your outdated driveline to be rebuilt your driveline will leave our store within 36 hours after being received. Don't see what you need just contact us toll free (800-216-1632), free technical support.

Drivetrain’s single-piece driveshafts are transported assembled and ready to install completely from the box. Our shafts are factory balanced for guaranteed performance, along with a lengthy service life. Simply eliminate your outdated drive shaft and install the newest one in its place.

See general applications guide/table below, don't see what you need just give our Driveshaft Technical expert a call toll free 800-216-1632, free technical support.  

Further information is provided on other company’s driveline’s or driveshaft’s is provided in first table below.  With the second table just click component part number to have more information or to place an order online.

Driveshaft Chevy Colorado Parts

We can also provide both new and good take out Driveshaft parts individually, our GTO program is designed to save you money!   Large stock of Dana Spicer and NEAPCO  inventory includes:

• Yoke Shafts
• Weld Yokes
• End Yokes
• Stub shaft ends
• Slip Yokes
• U-joints
• Tubing

---

To ensure exact replacement driveshaft for your application we will need to know the following information:

Make, model and year of vehicle
Manual or Automatic transmission, with or without external overdrive
3, 4,  5 or 6 speed transmission
Model number of transfer case (if 4WD)
Engine size and type (diesel or gasoline - 4, 6, or 8 cylinder)
Series of drive shaft (if you know it)
Wheel base of vehicle
Measure from center of ujoint front to back center of ujoint
Location of Driveshaft (front or rear)

Don't see what you need just give our Driveshaft Technical expert a call toll free 800-216-1632, free technical support.