Send us you existing driveline we will rebuild & high speed balance it and you save money at least 20%!

Complete Drive Line and Driveshafts Service for All Mitsubishi Vehicles. Custom, New OEM units and rebuilt driveline's.   We offer a complete line of new Spicer Dana and NEAPCO end yokes, u-joints, and flanges, existing shafts shortened or lengthened.

Heavy duty commercial units are one of our main specialties, including farm, construction, golf course, mining and PTO equipment. Double and single Cardan CV joint shafts manufactured for vehicles with angle problems. See general applications, don't see what you need just give us a call toll free 800-216-1632, free technical advise.

Need help or tips with u joint repair tips for Mitsubishi as well as lowered or lifted cars, just give us a call we can help you remove vibration problems. See our free information on how to maintain or troubleshoot driveline's and driveshafts including angle phasing issues.

Drivelines/Driveshafts, Rear Ends, Overdrive Units, Manual Transmissions and Transfercases, Full Service Shop located in Reno/Sparks Nevada, 800-216-1632 give us a call or stop bye and say hello.

Further information  in table below is provides for other company’s driveline’s or driveshaft’s we provided . 

BMW	Chevy/GM	Dodge Car	Dodge Mitsubishi			G Series Chevy	Honda Ridgeline
Jaguar	J10 Jeep Mitsubishi	Jeep Cherokee	Jeep Commander	Jeep Grand Wagoneer	Jeep Liberty	KIA	Lexus
Mazda	Mercedes	Mercury	Mitsubishi	Nissan	Subaru	Toyota

Vibrations Problems Mitsubishi

This challenge is usually caused by used or worn u-joints or dings and dents in lyour driveline tubing. We can offer support and tips for u joint maintenance for your Mitsubishi Mitsubishi. 

Running raised vehicle with larger tires, are you changing the transfer case model, or transmission. If you have a two piece driveshaft it's important to balance the complete assembly at the same time, just contact us (800-216-1632) we will help you get rid of vibration problems. See our free information above on how to keep up or troubleshoot drivelines and with angle phasing concerns.

Failure Symptoms of Mitsubishi Driveline

New or strange noises from under the vehicle are a symptom of a problem with the driveshaft. These noises can emulate from the following:

• Failure of Transmission or T-Case rear bushing/seal or driveshaft center support bearing will facilitate driveshaft malfunction. Driveshaft U-joints excessive wear or failing will interfere with the driveshaft’s ability to rotate properly. This will cause; rattling, clunking, scraping, or even squeaking sounds.
• U-joints might be operating dry of lubrication may also produce a squeaking noise at lower speeds. Clicking or knocking sounds specifically can indicate a faulty CV joint. Any noises such as these are an indicator that your vehicle is ready for maintenance. Problems with turning the vehicle is another likely sign of a bad driveshaft. A broken driveshaft can prevent wheels from turning properly, giving you trouble when trying to make turns. This issue limits your overall control of the Mitsubishi. These issues can prevent you from driving the  Mitsubish correctly.

Shuddering Problem with Mitsubishi Driveshafts

Experiencing a significant shudder when accelerating from low speed or a stopped position, it can be another sign of failing driveshaft component. A U-joint or bad center bearing within the driveshaft may cause the faltering acceleration. You may also hear sounds while the Mitsubishi is shuddering from the worn-out U-joint. Driveshaft  failure at freeway speeds is traumatic, don’t let it happen to you or your wife.

Mitsubishi  Modifications

Vehicles with 4wd tend to be harder on the driveshafts. We offer both front and rear shafts plus customized shafts (for your application) if required. New OEM shafts as well as re-manufactured drivelines are available, let us repair your existing driveline assembly and you save money.

When you are modifying your vehicle the drivelshaft often needs modifying to; Lifting or lowering the suspension, swapping transmissions or axles, 4x4s, customs, all of these things usually require drive shaft modification to be done correctly. 

We are able to fabricate over 40 different drivelines configuration for the Mitsubishi. We also provide a  full assortment of new Spicer Dana and NEAPCO yokes, u-joint parts, and flanges, existing  shafts reduced or lengthened.

Also, heavy duty industrial shafts are one of our primary products areas such as over the highway 18 wheeler, farming, building, construction and mining shafts. We also have a large stock of power take off shaft (PTO). Double and individual CV joint shafts created for vehicles with perspective problems (angle) are available, along with shafts designed to your particular engineering and design specs.

The essential function of your driveshaft is always to transmit energy from a point (rear of transmission or transfer case to another point with constant action. In construction, vehicls and Mitsubishis, the drivetrain was created to send torque through angles from your transmission for the axle (or auxiliary transmission). The driveshaft must go through

constantly changing general viewpoints (angles) in the middle the transmission and axle. It must also be able to transforming size while transmitting torque (by way of the slide yoke). rides suspended by springs inside an unusual, hovering motion. This indicates the driveshaft must have the capacity to broaden, change and contact working perspectives, when experiencing protrusions or depressions. This is often accomplished through common joint parts, which permit the driveline to be used at divergent angles, in addition to slip yokes, which allow contraction or growth to happen.

When your drive/shaft  is not well-balanced with all the genuine yoke and U-joint components, you could have not repaired the possible vibrations. Our facility features the newest in driveshaft  production, and precision equipment and tooling. 

High Speed Balancing is the key to making you vibrations free  and improve efficiency and life of your Mitsubishi!

A driveshaft is not planning to operate clear and vibrations free unless it is right plus in balance. Our shafts are, right after set up and before welding, pre-straighten inside a unique hydraulic tool, it is actually straightened to improve than factory specifications. We then dynamically high speed harmony of the whole shaft assembly.

Want to review our detailed high quality  driveline manufacturing process we have provided a detailed video. We also specialize in high end service, if you are delivering to us your outdated driveline to be rebuilt your driveline will leave our store within 36 hours after being received. Don't see what you need just contact us toll free (800-216-1632), free technical support.

Drivetrain’s single-piece drivelines are transported assembled and ready to install completely from the box. Our shafts are factory balanced for guaranteed performance, along with a lengthy service life. Simply eliminate your outdated drive shaft and install the newest one in its place.

Mitsubishi Driveshaft Parts

We can also provide both new and good take out Driveshaft parts individually, our GTO program is designed to save you money!   Large stock of Dana Spicer and NEAPCO  inventory includes:

• Yoke Shafts
• Weld Yokes
• End Yokes
• Stub shaft ends
• Slip Yokes
• U-joints
• Tubing

To determine replacement driveshaft by application we will need to know the following:

• Make, model and year of vehicle
• Manual or Automatic transmission, with or without overdrive
• 3,4, or 5 speed transmission
• Make and model of transfer case
• Engine size and type (diesel or gasoline - 4, 6, or 8 cylinder)
• Series of drive shaft (if you know it)
• Wheel base of vehicle
• Location of Driveshaft (front or rear) 

 If it's a part and or components under your vehicle we can supply it!