These quality manual transmission parts and rebuild parts kits are designed to be top of the line overhaul kits. 

The following reference table is supplied to assist you in identification of the correct transmission, after locating correct unit a link is supplied to provide detailed information on specific kit and parts that are available for your unit.

Chrysler 4 and 5 speeds

CHRYSLER CORPORATION 4 SPEED TRANSMISSIONS:    
NEW PROCESS A833 1964-80 Cars, 1973-90 Trucks & Vans Parts List 82
  Aluminum or cast iron side loaded case with a rectangular 10-bolt side cover. Fully synchronized in all forward gears with brass synchro rings. 1975-90 units have Overdrive that is indicated by the 3rd gear in the cluster being larger than the 4th (on the end).    
NEW PROCESS 420 1956-68 Trucks ALTBK267I  
  Case iron top loaded case and top cover with tower shift. Non-synchronized in 1st and 2nd gears with ring/pin assembly for 3rd and 4th gears.    
NEW PROCESS 435 1963-90 Trucks Parts List 83
  Cast iron, top loaded case with an aluminum top cover with tower shift. Non-synchronized in 1st gear with aluminum ring/pin assembly for 2nd-4th gears.    
  Cast iron top loaded case and an aluminum top cover with tower shift. Fully synchronized in all forward gears with ring/pin synchros for 1st-4th gears.    
CHRYSLER CORPORATION 5 SPEED TRANSMISSIONS:    
NEW PROCESS A535 / 2500 1987-92 Dakota Parts List 84
  Aluminum, end loaded case with an aluminum rectangular 4-bolt inspection cover on top. The shifter is on top of the extension housing. Front and rear cluster bearings are tapered. The front bearing retainer has four bolts.    
AISIN WARNER AX15 1991-97 Trucks, including Dakota Parts List 104
  Aluminum, end loaded case based on the Toyota "R" series design. Front and rear cluster bearings are cylindrical roller. The front bearing retainer has eight bolts.    
NEW VENTURE 3500 1994-97 Trucks, including Dakota Parts List 50
  Aluminum, end loaded case with integral bellhousing. Front and rear cluster bearings are cylindrical roller. The front bearing retainer has six bolts.    
GETRAG 360
1988-93 Cummins Turbo Diesel Trucks Parts List 49
  Cast iron, top loaded case with an aluminum top cover and tower shift. The shifter is at the front of the top cover. "Getrag" is cast into the side of the case. The main bearings and the pilot bearing inside the input shaft are all tapered.    
NEW VENTURE 4500 1992-97 Trucks Order K100319 Parts List  
  Cast iron, top loaded case with an aluminum top cover and tower shift. The shifter is at the rear of the top cover. The main bearings are tapered while the input pocket bearing is a caged needle bearing.    
NEW VENTURE 5600 98 up Trucks    
  6 Speed heavy duty transmission, integrated bell housing Dodge only Parts List  
AMC / JEEP 3 SPEED TRANSMISSIONS:    
BORG-WARNER T84 1941-45 Jeep ALTBK376  
  Top loaded, cast iron case with non-synchronized 1st gear and 24 tooth 2nd/3rd synchro rings. Main shaft 1st/Reverse gear has 25 helical or straight cut teeth.    
BORG-WARNER T86 1946-72 Jeep, 1957-67 AMC Cars ALTBK288  
  Top loaded, cast iron case with non-synchronized 1st gear and 24 tooth 2nd/3rd synchro rings. Main shaft 1st/Reverse gear has 27 helical cut teeth.    
BORG-WARNER T90 1946-72 Jeep, 1959-67 AMC Cars Parts List 38
  Top loaded, cast iron case with non-synchronized 1st gear and 30 tooth 2nd/3rd synchro rings. Main shaft 1st/Reverse gear has 29 straight cut teeth.