Ring & Pinion Rear End Parts Chrysler Dodge 9.25 Inch
|
|
Having problems with your Dodge pickup 9.25 inch rear end, we offer a complete line of rear end/Differential Ring and Pinion Sets and parts. For the Chrysler 9.25 inch differential; our inventory includes ring gear and pinion sets, including aftermarket and OE gear sets. You can purchase high quality ring and pinion sets in various ratios,high quality bearing rear end bearing overhaul kits including pinion bearings, pinion seal, crush sleeve, pinion nut, shims, ring gear bolts, marking compound and gasket are included. We also supply axles, carriers, cases, positractions spider and side gears.
Positraction never get stuck again
Positraction units we offer include Lockright, Powertrax no-slip, Auburn, Detroit Lockers, Eaton TrueTrac and Trac Loc. Specifications are provided below to assist you in the identification and setup as well as torque specs for your Chrysler 9.25 differential. We are a Dana Spicer volume distributor and offer a complete line or ring gear and pinions and differential repair parts from the small 7.5-inch differential to the large Dana 80.
Along with our quality parts you have access to applications information for available ring and pinion ratios, information to assist you in identification of the differential that you have. Free information on ring and pinion installation is provided alone with specifications and carrier/case breaks when you are considering gear ratio changes. Free technical support for instalation if you buy your parts from Drivetrain.com. You can review applications available to assist you with selection of the specific positraction unit that you may need to improve your performance. Need more information call toll free 800-216-1632
Chrysler Dodge 9.25 Products
Click part number to see additional information or place order on line.
Chrysler 9.25" Ring & Pinion Gear
|
 |
|
Chrysler 9.25"Ring & Pinion Price List
|
Your gears run cooler and last longer!
Order above high performance synthetic oil and friction additive combo kit at time of order for ring and pinion or bearing overhaul kit and pay only $49.95 plus S&H, a $54.00 value. Quality guaranteed performance |
Chrysler 9.25" OE Ring & Pinion Price List
|
This gear set is a requirement for Van applications. Vans require very quite running gears; the van box can and will amplify the noise. |
|
Description |
Part Number |
Price |
 Installation Tool, Your Cost is $48.98 + S&H |
| Auburn Limited Slip (all ratio's) |
$464.10 |
||
| Detroit Truetrac 31 Spline more information & video | DTS913A368 | $663.93 | |
| Detroit Locker 31 Spline more information & video | DTS187C172A | $808.19 | |
| Dana Track-Loc |
$349.00 |
||
| LockRight Rear 1/2 & 3/4 Trk. 73-98 (31 spline) |
$361.40 |
||
| Powertrax no-Slip 31 Spline Open |
$458.55 |
||
| Powertrax no-Slip 31 Spline Trac-Loc Case |
$474.65 |
Chrysler 9.25" Differential Parts
|
Description |
Part Number |
Price |
|
| Case (Empty) |
$155.75 |
||
| Internal Parts Kit |
$156.67 |
TOUGH!
|
|
| Cross Shaft | MW9.25CS |
$15.58 |
|
| Loaded Case (Replacement for Chrysler OE) | SAX75102X |
$325.00 |
|
| Positraction Clutch stock repair kit 18/18 fric/disk includes clips |
$90.94 |
||
| Axle, (31 spline) 78 Car, 74-79 Trk. 100, 150, 4WD Ramcharger, 75-83 Trk. 100, 150, 2WD Ramcharger 31 11/16" Length |
$123.33 |
||
| Axle, (31 spline) 84-93 Trk. 100, 150, Ramcharger 31 5/8" Length |
$123.33 |
||
| Axle, (31 spline) 80-84 Trk. Ramcharger 31 5/8" Length |
$123.33 |
 This new Redline synthetic gear oil is recommended for replacement when replacing ring gear, pinion sets and or bearings, your cost only $9.95 qt. See other Red Line Oil Products that we recommend. |
|
| Seal, Axle | |||
| Seal, Pinion Yoke | |||
| Bearing, Axle 2.535 Outside Diameter | |||
| Differential Cover Vans, Ram 1500, Durangos & some Dakotas Increase the fluid capacity, you will find that the fluid will run 15 to 20 degrees cooler. |
$265.00 |
|
