
General Motors Overhaul Kits and Parts
Considering overhauling your Chevrolet 4T40E or T45E transmission? We provide a large inventory selection for T40E automatic transmission overhaul kits, parts including steels, kits, solenoids, filters, solenoids. This wide selection of parts are used in the GM 4T40E automatic transmission in GM Chevy Cavalier, Malibu, Sunfire, Grand AM, Oldsmobile Alero, Cutlass and Saturn LS. In addition to these kits we also supply torque converters, fluids, problem prevention kits and in most cases we can supply good take out hard parts and save you some money.
Free information is provided on parts illustrations, maintenance tips, overhaul tips and assistance in identifying just what automatic transmission you have in your vehicle. In addition a factory description and ratio information is available.
Considering overhauling your Chevrolet 4T40E or T45E transmission? We provide a large inventory selection for T40E automatic transmission overhaul kits, parts including steels, kits, solenoids, filters, solenoids. This wide selection of parts are used in the GM 4T40E automatic transmission in GM Chevy Cavalier, Malibu, Sunfire, Grand AM, Oldsmobile Alero, Cutlass and Saturn LS. In addition to these kits we also supply torque converters, fluids, problem prevention kits and in most cases we can supply good take out hard parts and save you some money.
Free information is provided on parts illustrations, maintenance tips, overhaul tips and assistance in identifying just what automatic transmission you have in your vehicle. In addition a factory description and ratio information is available.
Parts Illustration & large photo is available Troubleshooting/Overhaul Manual |
Maintenance Tips Overhaul Tips |
Remanufactured Automatic Transmission What transmission do I have? |
General Information
Description: Front wheel drive, electronically controlled, 4 speed, automatic overdrive transaxle with electronically controlled torque converter clutch. |
Ratios: 1st 2.957 2nd 1.623 3rd 1.000 4th 0.683 Rev 2.143 |
|
|||||||||
Engine Range: 1.5L - 3.1L |
Fluid Capacity: (approximate) Bottom Pan Removal: 7.0L (7.4qt) Complete Overhaul: 10.0L (10.6qt) Dry: 12.5L (13.2qt) |
Fluid Type: Positraction Unit for GM Front Wheel Drive's |
The following parts are available: | ||||
Part Number |
Qty Req |
Description |
Years |
Price |
TM4T40E | Troubleshooting/Overhaul Manual | 1995-on |
$48.97 |
|
MRK4200-S |
1 |
Master Rebuild Kit * | 1995-on |
$303.86 |
42170R |
1 |
Molded rubber pan gasket |
$30.46 |
|
K42900-4 |
1 |
Molded rubber clutch pistons |
$68.46 |
|
K52713H |
1 |
Low Reverse Band | 1995-on |
$47.13 |
K42980 |
1 |
Bushing Assortment Kit | 1995-on |
$70.94 |
K42940 |
1 |
Thrust Washer Kit (w/o Selective's) | 1995-on |
$15.45 |
K42900-4 |
1 |
Piston Kit (Complete) Molded Rubber | 1995-on |
$68.47 |
42813 |
1 |
Sprag Roller Clutch (12 Rollers) | 1995-on |
$24.42 |
42814 |
1 |
Sprag Input (22 Element) | 1995-on |
$69.07 |
42815 |
1 |
Sprag Low (Forward) Roller Clutch (16 rollers) | 1995-98 |
$25.25 |
42815C |
1 |
Sprag Low (Forward) Roller Clutch (16 rollers) | 1998-on |
$29.37 |
42888 |
1 |
Drive Chain (3/4" Wide - 42 Rocker Links 4T40E | 1995-on |
$78.33 |
42888B |
1 |
Drive Chain (7/8" Wide - 42 Rocker Links 4T45E | 1997-on |
$91.25 |
The following electronic components may or may not be required. The best way to determine this is by check/consulting computer code(s) or electronic scanner results. | ||||
Part Number |
Qty Req |
Description |
Years |
Price |
42871 |
2 |
A & B Shift Solenoids | 1995-on |
$33.87 |
51873 |
1 |
TCC Solenoid | 1995-on |
$31.28 |
42879 |
1 |
Force Motor (EPC) Solenoid | 1995-on |
$336.33 |
42877 |
1 |
Pressure Switch Manifold | 1995-on |
$72.56 |
42875 |
1 |
Turbine Speed Sensor (Stamped 32/33T) 4 Cylinder | 1995-on |
$18.92 |
42876 |
1 |
Turbine Speed Sensor (Stamped 35T) 6 Cylinder | 1995-on |
$21.45 |
Torque Converter ---- Torque Converter Information For this series transmission there are seven different possible torque converters. When rebuilding your transmission it is always recommended that you change the torque converter. When ordering the torque converter you must supply the four digit code off of the existing unit (located on sticker). The probabilities are: |
|||||
Code | Order Part Number | Code | Order Part Number | ||
FAFB | C55B or C55C | FLQB | C52C | ||
FDHB | C28C | FYHB | C49B | ||
FKEB | C29B | FZEB | C29B | ||
FLDB | C52B | FZPB | C29B | ||
FLHB | C52B or C52C | We only supply high quality remanufactured torque converters, your cost $136.95 + $50.00 core deposit. |
Miscellaneous Information and Specifications | ||
Maximum Engine Torque: 200 lb (271 Nm) |
Maximum Gearbox Torque: 325 lb (440 Nm) |
Maximum Speed Shift: 6500 rpm |
Maximum Gross Vehicle Weight: 4100 lb (1860 kg) |
7 Position Quadrant: P,R,N,OD,3,2,1 |
Shift Pattern: (2) two way on/off solenoids Shift Quality: Variable Bleed solenoids Torque Converter Clutch Pulse width modulated solenoid control |
Troubleshooting/Overhaul Manual
These manuals are typically 50 to 85 pages and contain both troubleshooting information and data to support overhaul, such as electronic data, illustrations and specific procedures and specifications. These are professional shop manuals which will give you the capability to diagnose problems, and evaluate repair options. If you decide to have your transmission overhauled at a local shop you will be armed with detailed knowledge of problems and potential fixes. This information should allow you to get the best deal, Always compare pricing for labor. If you supply the parts and ask for warranty in the end you will save money.
Typically contains gaskets and rubber kit, sealing rings, metal/rubber clad seals, friction plates, steel plates* , front and rear bushings, filter and where applicable Band* and/or Modulator*.
*not included if listed separately
Regular maintenance cycles and continued checking of fluid levels is critical to the life of your transmission. Operating temperature is the single most critical parameter effecting the life of the transmission. Keep the temperature down and fluid fresh helps the units typically last a very long time under normal driving conditions (no teenagers involved). We can supply a couple of aftermarket products to help you get the most out of your transmission:
Auxiliary Transmission Oil Cooler.
The Truco part number LPD4451 is an excellent auxiliary oil cooler to provide additional cooling capacity. The kit includes all parts required to mount the unit and connect to existing cooling lines. This is a typical do it yourself project. The unit typically mounts in front of the radiator. Your cost on this transmission life saving product is $54.94 plus shipping and handling.
Fluid Additive
Generally we don't recommend additives but we have found that the Lubegard "Automatic Transmission Protectant" at only $13.93 + S&H can:
- Prevent overheating, reducing transmission temperature up to 40 degrees F.
- Extend fluid life
- Eliminates transmission fluid foaming and oxidation
- Reduces wear throughout the transmission
- Elimates clutch chatter and torque converter shudder
- Softens and modifies harsh shifts
- Provides for smoother shifting
- Eliminates objectionable noises during shifts
- Keeps valves and governors free and frees stuck valves in valve bodies
- Raises the thermal and oxidative stability
- Only product that increases the fluids ability to transfer heat
- Contains no Ash
Always consult and follow owners manual for maintenance intervals and requirements.
Overhaul Tips
Before you tear into the transmission, we suggest you first study the troubleshooting/overhaul manual, add a bottle of our "Automatic Transmission Protectant" and put a few miles on the vehicle. This just might free valves and governors that are possible stuck in valve bodies. Be sure to get computer trouble code(s), see owners manual for technique to acquire malfunction codes. This will be a great assistance in diagnosing possible problems.
Twenty-One Steps to Successful Transmission Repair:
1) Do your research: locate any technical bulletins pertaining to your transmission, ask your dealers parts department for bulletins.
2) Clean the entire transmission, including the valve body.
3) Check pump, valve body and case for warpage.
4) Flat file pumps, valve bodies, and cases. Just a few strokes with the file to knock off high spots and handling burrs.
5) Check all pump gear clearances.
6) Check planet pinion end play and side to side motion.
7) Soak all planet assemblies.
8) Soak all friction materials for 15 - 30 minutes.
9) Make sure all steels are in usable condition or replace. Do not sand or tumble steels when used against High Energy friction materials.
10) Inspect all surfaces upon which a band will ride.
11) Replace all rotating oil control rings.
12) Check all oil control rings and rubber products in the bores for proper fit.
13) Check all major support bushings and bushings that control lube oil.
14) Pre-lubricate all bushings and thrust washers.
15) Pre-lube pumps.
16) Pre-fill torque converter.
17) Use available manuals to ensure proper specifications and clearances.
18) Set correct clutch and band clearances.
19) Take the time to set the total end play.
20) Use a torque wrench on all pumps and valve bodies.
21) Always double flush the cooling and cooling return lines to the radiator to remove particles trapped there.
Take your time, take your time, take you time!
Failure modes for torque converters manifest themselves in different ways: slow failure, i.e. loss of power over time, instant failure, i.e. input shaft spline failure. Following is a short list of problems and possible causes:
Complaint |
Possible Cause |
Reference/Fix |
Lockup Slip/Shudder | Redesigned TCC PWM solenoid | ATRA Bulletin #286 |
No Lockup/Slipping | Restricted hydraulic flow | ATSG Bulletin #92-46 |
No Lockup/Slipping | Clogged PWM solenoid | ATSAG Bulletin #93-39 |
Torque Converter Installation/Preparation
Many torque converter problems can be avoided with proper preparation:
1) Pre-thread converter bolts by hand to make sure there is no sign of stripped threads.
2) Check and clean crankshaft thoroughly. Change crank spacer (if applicable).
3) Use 320 grit sandpaper or Emory cloth to remove any metal shavings on crankshaft.
4) Check converter for any damage that may have occurred during shipping.
5) Pre-fill converter with a minimum of (1) quart of transmission fluid.
6) Clean all paint off the pilot using 320 grit emory cloth.
7) Apply grease, not transmission gel, on the pilot.
8) Check flexplate for cracks and be sure there is no more than .006" run out.
9) Make sure all engine dowel pins are in place and clean.
10) Make sure all electrical ground straps are properly connected.
11) Never, Never use an impact gun to install torque converter bolts. Driving a bolt into the converter cover will create a dimple on the lockup apply surface. Lockup clutch failure will occur when the lockup piston applies against and uneven surface. Grinding off on thread length from all lockup converter bolts is recommended to avert this type of failure.